Mezzanine Goods Floor Lift Telford

Magna Specialist Confectioners Ltd APPLICATION Lifting goods between levels PIT INSTALLED YES CONSTRUCTION High Lift Scissor Table MODEL / TYPE RLXY3-20/430-2C CAPACITY 2000KG – evenly distributed load TRAVEL / STROKE 4400mm (limit switch set at 4300mm) CLOSED HEIGHT 750mm - pit dimensions to be advised at PDI TOTAL RAISED HEIGHT 5050mm PLATFORM SIZE 2200mm long & 1790mm wide, with anti slip surface (tear plate) OPERATION 2,3 kW compact electro-motor with hydraulic pump unit and adequately sized oil tank wired to IP55 Standard. Power unit is located outside the Lift POWER SUPPLY 400 Volts, 3 phases, 50 Hz CONTROL VOLTAGE 24 Volts with IP55 insulated electrics TRAVEL SPEED Approximately 75 seconds to maximum height CYLINDERS Normally single acting precision made units complete with pipe break valve to prevent a rapid lowering speed in the unlikely event of a hydraulic hose failure. Delfleet anti corrosion, ETCH-Primer. WEIGHT Approximately 1500KG?s STANDARD FINISH Stainless Steel AISI304 platform, gates and handrails Mild steel RAL 9005; base frame and scissors Mild steel; axles, wheels and bolts CONTROLS Two (2) constant pressure UP & DOWN hand control units with EMERGENCY STOP button and 6 meter long cable SAFETY TRIP BAR Aluminium safety frame with built in safety function. If the safety frame is touched on its way down, the Lift stops immediately. To continue lowering, the table has to be raised a little to be able to lower again. MAINTENANCE Standard safety legs are provided to support the scissor lift mechanism in the raised position and must be deployed for all servicing and maintenance work INSTALLATION Fitted with lifting eye bolts for easy installation in pit if required HAND RAILS 1100mm high hand rails with 150mm high kick-boards, fitted to both long sides and one short side SAFETY GATES 1100mm high twin safety gate with 150mm high kick-boards fitted to one 1500mm side – outwards opening INTERLOCKING GATES The safety gates are interlocking into the control system of the lift so the platform will NOT raise or lower when the gates are open OTHER Landing legs and lift eye bolts for installation EN 1570 A Declaration of Conformity or Incorporation is issued with every Lift unit stating they have been manufactured to meet all requirements of current European Standards for scissor lifts GENERAL The lift is designed to operate on a firm even floor surface Table will be pit mounted. • Table will be supplied with a remote power pack for ease of change over, should a fault occur. A spare power pack will also be provided. • Supplied with a four sided enclosure to both levels measuring 2.50m long x 2.09m Wide - Manufactured in 304 grade stainless steel and finished with a silicone bead blast (to give an even matt finish to the stainless steel) • Ground floor: 3900mm high to the underside of the mezzanine floor. Incorporating a 2000mm high gate to one short side. • First Floor: 2100mm high. Incorporating a 2000mm high gate to one short side • Both gates will be fitted with electro-mechanical interlocks to prevent platform motion if either gate is open and to prevent the gates from being opened unless the platform is at the appropriate level To be installed at Magna Specialist Confectioners Ltd Magna House, Stafford Park 3 Telford Shropshire TF3 3BH Manual Handling Solutions (MHS.COM Ltd) offer bespoke custom design Goods Lifts, Mezzanine Floor Lifts, Mezzanine Goods Lifts, Material Lifts, Pallet Lifts to suit a wide range of different applications. All our goods lifts have a range of options and are built to suit individual customer requirements. Full details from Manual Handling Solutions (MHS.COM Ltd) 58, Paige Close Watlington, King's Lynn, Norfolk PE33 0TQ UK Tel 01553 811977 sales@manualhandlingsolutions.co.uk http://www.goodslift.website http://www.mezzaninefloorlift.co.uk

For more information on Mezzanine Goods Floor Lift Telford talk to Manual Handling Solutions, Goods Lifts