Metrel MI3102 Eurotest XE Installation Tester

Metrel MI3102 Eurotest XE Multifunction Tester

The Metrel MI3102 EurotestXE is a small and lightweight multifunction tester with many features.

After measurements have been completed, results can be stored to the 500 results capacity flash memory of the instrument. Test results, along with sub-results and function parameters can be organized and stored in a 3-level structure (i.e. Object x, Block X, Fuse X).

The test data can then be downloaded into Metrel's Eurolink XE Software from where you can create simple reports and export test data into a spreadsheet. The Eurolink XE Software is supplied with the MI3102 tester.

The Metrel MI 3102 Eurotest XE Multifunction tester allows you to test and certify fixed electrical installation in compliance with the Part P, 17th Edition regulations, BS7671 and BS EN61557. The 3002 Eurotest DL can perform a variety of electrical tests including: Continuity Testing, Insulation Testing, RCD testing including Ramp Test and a no RCD trip feature, Earth Loop impedance testing and PSC (prospective shirt circuit current. Basically all the tests you need to fully ensure safety within electrical installations in both commercial and domestic environments. The Metrel MI 3102 can even perform online voltage monitoring and phase sequence testing. It is the ideal unit for electricians and engineers performing high volumes of testing on TT, TN and IT Systems. Simultaneous testing of all possible values of Fault Loops, Isc and Rs Loop tests on both polarities enabled on IT systems as well as on 55V / 65V reduced low voltage systems.

The Metrel MI3102 is part of Metrel's innovative range of multifunction testers with checking and testing of safety conditions with PASS or FAIL evaluation.

Automatically calculating Ipsc with custom adjusted factor. An inbuilt table of Fuse Characteristics allows the Eurotest XE to indicate and Pass or Fail. This feature is exclusive to the Metrel range of testers.

The Metrel Eurotest XE can also carry out Earth Resistance Testing and come supplied with an Earth Spike Kit. Both two and three lead method is supported.

Testing RCD's could not be easier using the automatic 6 in 1 visit. Reset the breaker and the MI3102 will carry out all the tests needed. The RCD Ramp test will indicate actual trip current and the RCD Triplock feature will prevent any tripping of RCD's.

The Metrel MI3102 has an in built charging circuit and comes supplied with 6 of rechargeable NiMH AA batteries. The automatic Switch-Off function will also help save battery life when the tester is not in use. If you are a novice to using this tester, the Eurotest XE even has on-screen help guides describing how to perform a measurement.

The Metrel MI3102 Eurotest comes supplied in a soft carrybag that stores both your tester, test leads and any other accessories like Socket Adaptors and Kewtech Lightmates.

The Earth Spike is supplied in a separate Metrel carry case. Weighing under 1.3kg the Metrel Eurotest XE has taken both speed of testing and portability into consideration.

The long term reliability of this multifunction tester is guaranteed by Metrel's 3 year warranty and is ready for use with a Manufacturers Calibration Certificate also found within this kit.

The Metrel Eurotest XE Mi3102 can carry out a full range of Electrical Tests:

• Continuity Test - Carried out with standardized 200mA in both polarities.
• Insulation Test - on 100V, 250V, 500V and 1000V DC.
• RCD Auto Test
• RCD Ramp Test
• Loop Impendance with no trip feature
• Prospective Short Circuit Current (PSC)
• Multivoltage System Support
• Polarity Test
• Phase Sequence testing with voltage monitor between phases.
• Earth Resistance testing
• Leakage True RMS - (optional Clamp required - part no. A1018 / A1019)
• Light/Lux Measurements. (optional Lux Probe required - part no. A1172 / A 1173)

For more information on Metrel MI3102 Eurotest XE Installation Tester talk to www.test-meter.co.uk